Pure Energy ProjectElectrical · Heating · Plumbing07825 268 434 
Maida Vale & Little Venice · W9
A new fuseboard, with protection chosen for the circuits behind it.
PEP installs and replaces consumer units in Maida Vale W9, including new boards for agreed refurbishment and rewiring work and replacements for older fuse boxes. We assess the circuits and supply, explain the specification and complete the work with testing and certification.
From a mansion flat near Elgin Avenue to a house in Little Venice, we look at the installation you have, the reason for changing it and what the replacement needs to achieve. The work can be a standalone upgrade; it does not have to be part of a refurbishment.
Domestic Installer SchemeExisting installation
assessed before replacement
Installation, testing
and documentation
New installation · Replacement · Planned alterations
In a Maida Vale mansion flat or Little Venice house, we clarify the dwelling’s electrical supply, access and any building-management requirements before planning the board work. New circuits and retained circuits are identified separately rather than assuming a new enclosure resolves every existing issue.
For a refurbishment or rewire, we specify the consumer unit alongside the proposed circuits, assessed demand and incoming supply. The board, protective devices and circuit schedule form part of the installation design.
Replacing an existing fuse box is a different scope from rewiring the property. We assess the circuits that will remain and explain any required remedial work; a new board does not renew hidden cables.
An additional board or a different position may be considered for the agreed project. Suitability depends on the supply, circuit design, access and installation conditions. It is assessed and quoted, not assumed to be necessary.
You may have received an inspection report recommending changes, be unsure about an older fuse box or want to understand the protection available for your home. These are different starting points, and they deserve more than the same recommendation based on a photograph.
We establish why replacement is being considered and assess the relevant installation before proposing a board. The condition of the equipment, the existing protective arrangements and any findings from earlier inspections all matter.
If your main concern is a circuit that keeps tripping, tell us when it happens. An appliance or wiring fault may need investigation. Changing the consumer unit is not a substitute for finding the cause.
The arrangement inside the board affects which circuits lose power when a protective device operates. Where several circuits share one RCD, a fault on one of them can interrupt the others too.
Individual RCBO protection can help restrict that interruption to the affected circuit. Each RCBO protects its circuit against overloads and short circuits while also providing residual-current protection. It does not prevent every fault, and it cannot guarantee that the rest of the home will always retain power.
RCD protection helps reduce electric-shock risk by detecting certain imbalances in current. Surge protection has a separate role: limiting transient overvoltages that can affect connected equipment.
We explain the proposed devices in relation to your circuits, rather than leave you to choose between unfamiliar abbreviations. The specification follows the installation's needs and applicable requirements, including any other protective measures needed for the property.
A clear quotation
The quotation depends on whether this is a new consumer unit installation or a replacement, the circuit schedule, protection required and any agreed wiring or access work. These items are explained before installation; a board-only price should not be assumed to include new circuits or remedial work.
The cost is shaped by the installation and the agreed work, not simply by how many switches appear on the front of the old board.
When preparing a quotation, we consider:
A straightforward replacement and a job involving circuit repairs or a new board position need different allowances. We set out the proposed work so you can see what the price covers and which requests would be additional.
If you already have an Electrical Installation Condition Report, include it with your enquiry. It helps us understand the recommendations you have received, although it does not remove the need to assess the installation for the proposed work.
Maida Vale's red-brick mansion blocks and period houses provide a recognisable local setting, but neighbouring homes can have very different electrical arrangements. A converted flat may have been altered independently of the property above it; another apartment may have a more recent installation.
For a flat, we establish which consumer unit serves your home and whether access is needed to equipment elsewhere in the building. A meter cupboard controlled by a managing agent, for example, may need to be accessible for the appointment.
We also discuss the working area inside the property. Tell us about fitted cupboards, restricted access or finishes close to the existing board. Understanding these conditions early helps define a practical replacement without assuming that changes to communal electrical equipment are included.
Room to plan, not a promise of more power
Spare positions in a new consumer unit can be useful when planning future circuits. They do not, by themselves, establish that the installation can support a new electric shower, cooking appliance or heating system.
The proposed load, existing supply and relevant wiring must be considered together. An empty space in the enclosure is only one part of that discussion.
If you have a particular addition in mind, mention it before the replacement is specified. We can take a definite requirement into account and explain whether it involves work beyond the consumer unit. There is no need to turn a simple replacement into an open-ended renovation plan.
A practical plan for an occupied home
Suitable existing circuits can remain when a consumer unit is changed. We assess their suitability for reconnection and identify any associated work needed; the board's appearance alone cannot answer that question.
Our guide to replacing a consumer unit without assuming a full rewire explains how the condition of the connected circuits affects the appropriate scope.
Once the scope is understood, we discuss the anticipated interruption to your electricity and the access needed for installation and testing. Let us know about essential electrical equipment, home-working arrangements or other household needs that affect planning.
If additional defects become apparent, we explain the implications and discuss any change to the work and cost. Unsafe circuits cannot simply be reconnected to keep to an expected finish time.
Where substantial wiring renewal is necessary, it is a separate decision. Our Maida Vale house rewiring service covers that wider scope.
The handover should leave you able to recognise the circuits and understand the controls on the new board. We identify the circuits, explain the relevant operating and testing instructions, and record the completed work.
An Electrical Installation Certificate, including the associated inspection and test schedules, documents the replacement. It should be kept with your property records and read alongside any findings concerning retained parts of the installation.
For domestic consumer unit replacement in England, Building Regulations notification is also required. The resulting compliance documentation is separate from the electrical certificate. We explain the notification arrangements and how you will receive the records for your job.
Maida Vale · Little Venice · W9
We welcome fuseboard replacement enquiries across Maida Vale, including addresses in W9 1, W9 2 and W9 3. Local areas include:
Little Venice also includes addresses in W2, while parts of West Kilburn fall within W10. Send your full postcode so we can confirm the location and discuss the work. We can also check enquiries from neighbouring Paddington, St John's Wood and Queen's Park addresses.
For other electrical requirements, visit our Maida Vale electrical services page. Our London consumer unit replacement page provides an overview of the wider service.
Yes. The assessment needs to account for the flat's installation, the supply arrangement and any access required outside the apartment. Let us know if a concierge or managing agent controls the relevant cupboards or working areas.
That depends on the cause. A fault in an appliance, connection or circuit can remain after the board is changed. We distinguish between the need for improved protection and a problem requiring fault-finding, so the proposed work addresses the right issue.
It can where assessment confirms that it is suitable for reconnection. Any necessary repairs are explained as part of the scope. The fact that you need a consumer unit upgrade does not, on its own, establish a need to replace all the cables.
The circuits, chosen protective arrangement, access, isolation and condition of the existing installation all influence the quotation. Moving the board or adding circuits changes the scope, so mention those requirements when you first contact us.
No. They can reduce the number of circuits interrupted by certain faults, but a supply outage or a problem elsewhere can still affect the whole property. The aim is appropriate circuit protection, not a guarantee of uninterrupted electricity.
Not automatically. More space for protective devices does not increase the capacity of the incoming supply or existing cables. Tell us which equipment you are considering so its requirements can be assessed before any installation is agreed.
We explain the expected power-off period after assessing the job. Access may be needed to the consumer unit, the relevant supply equipment and points around the home for testing. The arrangements depend on your installation, rather than a standard time allowance for every replacement.
You receive the Electrical Installation Certificate with the inspection and test schedules, plus the separate Building Regulations compliance documentation through the applicable notification process. We explain what each document covers and any further recommendations relevant to your installation.
Yes. PEP installs new consumer units within agreed residential refurbishment and rewiring projects, as well as replacing existing boards. We assess the supply, proposed circuits and any wiring to be retained before specifying the equipment. An additional board or relocation is considered separately where the project requires it.
Talk to PEP
Tell us your postcode and whether you need a new consumer unit, a replacement or board work within a refurbishment or rewire. If there is no existing board, send your project plans and the proposed position. For an existing installation, photographs of the closed board and its surroundings are helpful. Do not remove covers or expose electrical parts to take photographs.
If it is safe to do so, send a photograph of the closed fuseboard and another showing the space around it. Leave every cover in place; there is no need to expose wiring or investigate the equipment yourself.
We will review the information and explain the next step towards a quotation for your home.